POWERFULL CLEANING “WET/DRY Soda Blaster”

You don't need to worry about powder dust in the air during operation, and even the installation space. Make DIY even more possible; cleaning, washing and polishing old automobiles and motorcycles as well as restoring parts.

 

 

Limited time sale for World Wide on Ebay!

 


Using baking soda as a main raw material in a blasting method

There are various kinds of powder (media) to be used, such as sand, glass, alumina, etc. Ability and the finish are different depending on what media is used. EZ Blust uses baking soda as water-soluble media that is harmless to the human body and environment.


One unit enables to process in either dry or wet settings

By our own-developed nozzle, EZ Blust is capable of spraying the media in either dry or wet settings, or spraying only water.


Finish and usability - Unique to baking soda media

Plating will not get fogged up when removing the rust from plated parts. Since it is water soluble, it can be applied to delicate materials, movable parts and sealed parts. The finish will not be excessively scraped due to low Mohs hardness.


Base materials will be rust resistant after application

By using baking soda media, EZ Blust will coat the object with an alkaline film which limits the acceleration of corrosion and rust. It is practical because it is fine to have time interval until a next time of applying rust preventive materials.



 

The  water-soluble media - together with water and compressed air, to strongly clean and polish things. 

It is possible to use it ashigh-pressure washing machine and sandblasting.


Good Point

No.1 Baking soda as a main raw material is environmentally friendly.

No.2 This "magic powder" melts in water at normal temperature and does not remain in the material. The environmental-impact is low as it does not pollute or even remain in the water.

No.3 Mohs hardness of the raw material is as low as 2.5 of 10 which enables to clean any materials without damaging.


Major applications and purposes

  • ・Automobiles and construction machines
  • ・To wash a car body (dirt, rust, oil component) and to clean vehicle suspensions, around engines, paint peeling and parts in maintenance repair
  • ・To wash boats and boat hulls (dirt, rust, oil component), decks, machine rooms, engine parts, paint peeling and to remove barnacles
  • ・To clean buildings, interior and exterior walls, bricks, to remove paint film and graffiti (ink, paint and oil) as well as for concrete surface roughening and painting groundwork processing
  • ・To remove deterioration and stains from concrete surfaces, rust on reinforcing steel, signboards, tents, parking lots and as well as for the last cleaning of construction areas
  • ・To clean memorial monuments, outdoor monuments, filters and ducts of air conditioner units
  • ・To clean inside and outside of bathtubs, floors and walls of bathrooms, gravestones and to remove oil stains from asphalt and concrete

 

Q.1 How much specification is necessary for the air compressor?
A.1 A compressor with at least 3 horsepower or above is recommended for a certain degree of continuous work. 5 horsepower or above is highly recommended for professional users and heavy users.

Q.2 Does water flow back to the media ejection line by the switching nozzle of dry and wet?
A.2 Only the case, which you open the valve of the media regulator with no pressure in the tank and close the outlet of the nozzle, will be causing flow backwards.

Q.3 Is it possible to remove dirt on the surface of wood?
A.3 Yes, it can also be used cleaning the surface of wood. But it may roughen the surface. If you use dry and wet switching properly, subsequent process may be easier. Baking soda due to low Mohs hardness makes this possible.

Q.4 How much MPa is preferred?
A.4 Around 0.6 MPa is recommended. It is possible to work at around 0.4 MPa if you use it well. Please note that safety valve opens when exceeding 1 MPa.

Q.5 How much the baking soda media should be put in the tank?
A.5 You can fill up to three quarters (about 20kg/ 44lb) if you are working continuously. Ideally 10kg (22lb) should be added each time the media runs out.

Q.6 Should I use it in a closed room/space when using it with the dry setting?
A.6 It is not necessary, but please consider the surrounding environment since powder dust scatters.

Q.7 Is it possible to use the baking soda media once again which is used?

A.7 It is not possible to use again in case of Wet blow because of water-soluble media. It can be reused in case of Dry blow inside of a cabinet, however, capability of cleaning will be dropped.

Q.8 How to solve when the media does not come out stably?
A.8 Please try adjusting the machine setting for flow rate of the media and air. Turn fully the gold knob at the top of the tank clockwise to the maximum flow. And gradually turn back the knob to a point where the media injects cleanly and continuously. If it does not work, probably the media in the tank becomes less, or the media is hardened by moisture.

Q.9 How much baking soda to be used?
A.9 Approximately 330g (11.6oz) per minute is average usage, and adjustable range is about 100g to 1,000g (3.52oz to 35.2oz). Please apply appropriately to the material and its condition. Also please control the speed of the adjustment knob according to the condition of the media and remaining amount in the tank.

 

We exhibited at the SEMA show

We received a lot of high praise. We want to deliver EZ Blust to users all over the world!

Interested in selling EZ Blust in your country?
We are looking for Distributors & Dealers.
Please contact.

info@ezblust.com

 

 

Limited time sale for World Wide on Ebay!

 

Other countries are also preparing.

Please contact us.

info@ezblust.com